Basler A202k User Manual Page 105
- Page / 118
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Troubleshooting
BASLER A202
k 6-1
DRAFT
6 Troubleshooting
6.1 Fault Finding Using the Camera LED
When the power supply to the camera is switched on, the LED on the back of the camera will
become orange colored for several seconds as the microprocessor in the camera boots up. If the
LED then remains orange continuously, bootup has been successful.
Once bootup is complete, the camera performs a continuous series of self checks. If an error
condition is detected, the LED will begin to flash between green and orange. The number of
orange flashes indicates the detected error (see Table 6-1). If several error states are present, the
LED outputs the error codes in succession.
If the status LED on the back of the camera is not lit, it means that power to the camera is not
present or is less than 10.8 Volts.
LED Description
On
Continuous
The camera is OK.
3 flashes ExSync has not changed state for 5 seconds or longer. If you are not supplying
an ExSync signal to the camera, this is a normal condition and should be ignored.
Otherwise check the cable and the ExSync generating device.
5 flashes
The Work Set could not be stored into a User set.
Please contact Basler technical support.
6 flashes
A User Set or the Factory Set could not be loaded into the Work Set.
Please contact Basler technical support.
7 flashes A valid list of commands was not available.
Please contact Basler technical support.
8 flashes
The FPGA could not be configured. Please contact Basler technical support
Table 6-1: Camera Status Indications
L
The camera has no overvoltage protection. Always observe the maximum
input voltage given in Section 2.8.
- Basler A202k 1
- Table of Contents 5
- 5 Mechanical Considerations 8
- 1 Introduction 9
- Introduction 10
- 1-2 BASLER A202 10
- 1.3 Spectral Response 11
- 1.5 Precautions 13
- 2 Camera Interface 15
- 2.1.2 Pin Assignments 16
- 2.1.3 Connector Types 17
- 2.2 Cable Information 18
- Camera Interface 19
- 2.4 Input Signals 20
- 2.5 Output Signals 21
- 2.5.4 Video Data 22
- Video Data Sequence 23
- 2-12 BASLER A202 26
- 2.8 DC Power 29
- 2.9 Status LED 30
- 3.1 Functional Description 31
- Operation and Features 32
- 3-2 BASLER A202 32
- 3.2 Exposure Time Control 33
- 3.2.2 Free-run Operation 40
- 3.3 Video Data Output Modes 42
- 3.4 Integrate Enabled Signal 42
- 3.5 Gain and Offset 43
- 3.5.1 Setting the Gain 44
- 46
- 3.5.3 Setting the Offset 48
- 3.6 Digital Shift 52
- Shift Twice 53
- No Shift 53
- Shift Once 54
- 3.7 Area of Interest (AOI) 56
- 3.7.1 AOI Setup Guidelines 57
- TIMING CHART IS NOT TO SCALE 59
- 3.8 Binning 60
- 3.9 Mirror Image 61
- 3.11 Test Images 63
- 3.11.2 Test Image Two 64
- 3.11.3 Test Image Three 64
- 3.12 Configuration Sets 65
- 3.13 Camera Temperature 66
- 3.14 Camera Status 66
- 4 Configuring the Camera 67
- 4.1.4 Configuration Tool Help 70
- Programming Commands 71
- 4.2.2 Error Checking 74
- 4.2.3 Example Commands 75
- Configuring the Camera 77
- 4-12 BASLER A202 78
- 4.2.4.3 Timer 1 79
- 4.2.4.4 Timer 2 79
- 4.2.4.5 Digital Shift 80
- 4-16 BASLER A202 82
- 4.2.4.10 Left Side Gain 83
- 4.2.4.11 Left Side Offset 83
- 4.2.4.12 Right Side Gain 84
- 4.2.4.13 Right Side Offset 84
- 4.2.4.14 Horizontal Binning 85
- 4.2.4.15 Vertical Binning 85
- 4.2.4.16 Mirror Image 86
- 4.2.4.17 Test Image Command 87
- 4.2.5 Query Commands 88
- 4.2.5.4 Read Serial Number 89
- 4.2.5.5 Read Camera Version 89
- 4-24 BASLER A202 90
- 4.2.5.10 Reference Values 92
- 4-28 BASLER A202 94
- 4.2.7 Camera Status Command 96
- 4.2.8 Bitrate Command 97
- 4.2.9 Camera Reset Command 98
- Mechanical Considerations 101
- BASLER A202 101
- 5-4 BASLER A202 102
- Equipped Cameras 103
- 5-6 BASLER A202 104
- 6 Troubleshooting 105
- 6.2 Troubleshooting Charts 106
- Troubleshooting 107
- 6.2.2 Image Quality Problems 108
- 6.2.3 Interfacing 109
- Revision History 113
- Added Section 6.3 114
- Feedback 115
Related products and manuals for Bridge cameras Basler A202k
Bridge cameras Basler Camera User Manual
(244 pages)
(244 pages)
Bridge cameras Basler A400K User Manual
(130 pages)
(130 pages)
Bridge cameras Basler Camera User Manual
(5 pages)
(5 pages)
Bridge cameras Basler A400K User Manual
(242 pages)
(242 pages)
Bridge cameras Basler SCOUT LIGHT User Manual
(228 pages)
(228 pages)
Bridge cameras Basler A101f User Manual
(66 pages)
(66 pages)
Bridge cameras Basler A102f User Manual
(120 pages)
(120 pages)
Bridge cameras Basler raL2048-48gm User Manual
(238 pages)
(238 pages)
Bridge cameras Basler SCOUT LIGHT User Manual
(166 pages)
(166 pages)
Bridge cameras Basler Camera User Manual
(11 pages)
(11 pages)
Bridge cameras Basler A101f User Manual
(46 pages)
(46 pages)
© 2020, manymanuals.com. All rights reserved. | 1.563 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals