Basler A202k User Manual Page 109
- Page / 118
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Troubleshooting
BASLER A202
k 6-5
DRAFT
6.2.3 Interfacing
Use the interfacing troubleshooting charts if you think that there is a problem with the cables
between your devices or if you have been directed here from another chart.
Interfacing Chart
Always switch off power to the system before making or breaking any connection.
Reseat the cable connections at the camera and the frame grabber.
After you reseated the connections, is the problem still present?
Replace the
power source
Yes
No
If extra hardware is available, try to locate the problem by
substitution. (Substitute only one piece of hardware at a time and
retry the system after each substitution.)
After you finished making substitutions, is the problem still present?
Exit this
chart.
If you have not already done so, use a voltmeter to check the power
source for the camera. The output must be 12 VDC ± 1.2 V. Also, make
sure that the power source meets the other specs shown in Section 2.8.
Is the power source OK?
No
Yes
No
Exit this
chart.
Yes
Yes
No
Exit this
chart.
No
Exit this
chart.
Contact Basler technical support. The contact numbers appear on the title page of this manual.
Before you call for support, be sure to make note of the camera settings and the frame grabber settings
you are using. You should also have a captured live image and a captured test image available. Technical
support will frequently request that you e-mail copies of these captured images.
Yes
Check the configuration file that you are using with your frame grabber, e.g. the DCF or
ICD file. Make sure that it is the correct file for the Basler A202
k. Be aware that sometimes
different configuration files must be used depending on which of the camera’s features
you have enabled.
Configuration files for many types of frame grabbers are available at the Basler web site:
www.basler-vc.com. These files have all been tested with the A202
k and we suggest that
you use them if one is available for your type of frame grabber.
After you checked the DCF file, is the problem still present?
Check all of the cables in the system:
Check Section 2.2 of this manual and make sure that you are using a cable that has the
right characteristics and is not too long. It is extremely important to use the proper cables
when you are working with Camera Link based cameras.
Use an ohm meter to check each wire to see if it is broken or shorted to any of the other
wires in the cable.
After you checked the cables, is the problem still present?
- Basler A202k 1
- Table of Contents 5
- 5 Mechanical Considerations 8
- 1 Introduction 9
- Introduction 10
- 1-2 BASLER A202 10
- 1.3 Spectral Response 11
- 1.5 Precautions 13
- 2 Camera Interface 15
- 2.1.2 Pin Assignments 16
- 2.1.3 Connector Types 17
- 2.2 Cable Information 18
- Camera Interface 19
- 2.4 Input Signals 20
- 2.5 Output Signals 21
- 2.5.4 Video Data 22
- Video Data Sequence 23
- 2-12 BASLER A202 26
- 2.8 DC Power 29
- 2.9 Status LED 30
- 3.1 Functional Description 31
- Operation and Features 32
- 3-2 BASLER A202 32
- 3.2 Exposure Time Control 33
- 3.2.2 Free-run Operation 40
- 3.3 Video Data Output Modes 42
- 3.4 Integrate Enabled Signal 42
- 3.5 Gain and Offset 43
- 3.5.1 Setting the Gain 44
- 46
- 3.5.3 Setting the Offset 48
- 3.6 Digital Shift 52
- Shift Twice 53
- No Shift 53
- Shift Once 54
- 3.7 Area of Interest (AOI) 56
- 3.7.1 AOI Setup Guidelines 57
- TIMING CHART IS NOT TO SCALE 59
- 3.8 Binning 60
- 3.9 Mirror Image 61
- 3.11 Test Images 63
- 3.11.2 Test Image Two 64
- 3.11.3 Test Image Three 64
- 3.12 Configuration Sets 65
- 3.13 Camera Temperature 66
- 3.14 Camera Status 66
- 4 Configuring the Camera 67
- 4.1.4 Configuration Tool Help 70
- Programming Commands 71
- 4.2.2 Error Checking 74
- 4.2.3 Example Commands 75
- Configuring the Camera 77
- 4-12 BASLER A202 78
- 4.2.4.3 Timer 1 79
- 4.2.4.4 Timer 2 79
- 4.2.4.5 Digital Shift 80
- 4-16 BASLER A202 82
- 4.2.4.10 Left Side Gain 83
- 4.2.4.11 Left Side Offset 83
- 4.2.4.12 Right Side Gain 84
- 4.2.4.13 Right Side Offset 84
- 4.2.4.14 Horizontal Binning 85
- 4.2.4.15 Vertical Binning 85
- 4.2.4.16 Mirror Image 86
- 4.2.4.17 Test Image Command 87
- 4.2.5 Query Commands 88
- 4.2.5.4 Read Serial Number 89
- 4.2.5.5 Read Camera Version 89
- 4-24 BASLER A202 90
- 4.2.5.10 Reference Values 92
- 4-28 BASLER A202 94
- 4.2.7 Camera Status Command 96
- 4.2.8 Bitrate Command 97
- 4.2.9 Camera Reset Command 98
- Mechanical Considerations 101
- BASLER A202 101
- 5-4 BASLER A202 102
- Equipped Cameras 103
- 5-6 BASLER A202 104
- 6 Troubleshooting 105
- 6.2 Troubleshooting Charts 106
- Troubleshooting 107
- 6.2.2 Image Quality Problems 108
- 6.2.3 Interfacing 109
- Revision History 113
- Added Section 6.3 114
- Feedback 115
Related products and manuals for Bridge cameras Basler A202k
Bridge cameras Basler Camera User Manual
(244 pages)
(244 pages)
Bridge cameras Basler A400K User Manual
(130 pages)
(130 pages)
Bridge cameras Basler Camera User Manual
(5 pages)
(5 pages)
Bridge cameras Basler A400K User Manual
(242 pages)
(242 pages)
Bridge cameras Basler SCOUT LIGHT User Manual
(228 pages)
(228 pages)
Bridge cameras Basler A101f User Manual
(66 pages)
(66 pages)
Bridge cameras Basler A102f User Manual
(120 pages)
(120 pages)
Bridge cameras Basler raL2048-48gm User Manual
(238 pages)
(238 pages)
Bridge cameras Basler SCOUT LIGHT User Manual
(166 pages)
(166 pages)
Bridge cameras Basler Camera User Manual
(11 pages)
(11 pages)
Bridge cameras Basler A101f User Manual
(46 pages)
(46 pages)
© 2020, manymanuals.com. All rights reserved. | 0.658 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals