Basler raL2048-48gm User Manual Page 109
- Page / 238
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
AW00118302000 Acquisition Control
Basler racer GigE 99
Use Case 3 - Acquisition Start and Line Start Triggering Off (Free Run),
Frame Start Triggering On
Use case three is illustrated on page 122.
In this use case, the Acquisition Start Trigger Mode and the Line Start Trigger Mode parameters are
set to off. The camera will internally manage acquisition start and line start trigger signals without
any need for triggering by the user ("free run").
The Frame Start Trigger Mode parameter is set to on, requiring that a frame start trigger signal is
applied to the camera.
The rate at which the camera will acquire lines will normally be determined by the camera’s
Acquisition Line Rate Abs parameter. If the Acquisition Line Rate Abs parameter is disabled, the
camera will acquire lines at the maximum allowed line rate. Note that the overall line rate will also
depend on the frame start trigger signal: Lines will only be acquired after a related preceding frame
start trigger signal has transitioned.
In this example, each frame is set to include three lines.
When the Acquisition Mode is set to Continuous Frame, the camera will be set to acquire frames
until an acquisition stop command is issued.
- Basler racer 1
- Table of Contents 5
- Basler racer GigE iii 7
- Basler racer GigE v 9
- 1.1 Models 11
- 1.2 General Specifications 12
- 1.3 Spectral Response 16
- 1.4 Mechanical Specifications 17
- Photosensitive Surface 18
- 1.4.2 Sensor Line Location 19
- 1.4.3 Lens Adapter Dimensions 20
- 1) 1) 22
- 1.5.1 LWIP TCP/IP Licensing 23
- 1.5.2 LZ4 Licensing 24
- Basler racer GigE 15 25
- 1.7.2 Heat Dissipation 26
- 1.8 Precautions 27
- Warranty Precautions 28
- Read the manual 29
- 20 Basler racer GigE 30
- 2 Software and Hardware 31
- Installation 31
- 22 Basler racer GigE 32
- 3 Tools for Changing Camera 33
- Parameters 33
- 3.3 The pylon SDK 34
- 4 Basler Network Drivers and 35
- 4.1 The Basler Filter Driver 36
- Basler racer GigE 27 37
- General Parameters 38
- Basler racer GigE 29 39
- Basler racer GigE 31 41
- Adapter Properties 44
- 36 Basler racer GigE 46
- 5 Network Related Camera 47
- Parameters and Managing 47
- Bandwidth 47
- 38 Basler racer GigE 48
- Basler racer GigE 39 49
- 40 Basler racer GigE 50
- Basler racer GigE 41 51
- 44 Basler racer GigE 54
- 6 Camera Functional 55
- Description 55
- Basler racer GigE 47 57
- Fig. 12: Camera Block Diagram 57
- 48 Basler racer GigE 58
- 7 Physical Interface 59
- 7.1.1 Pin Numbering 60
- 7.2 Connector Pin Assignments 61
- 7.3 Connector Types 63
- 7.4 Cabling Requirements 64
- 7.4.2 I/O Cable 65
- 7.4.3 Ethernet Cables 65
- 7.5 Camera Power 66
- 7.6 Input and Output Lines 67
- Basler racer GigE 59 69
- Using the Inputs with LVTTL 70
- 7.6.1.2 Input Line Debouncers 71
- 7.6.1.3 Input Line Inverters 72
- Function 72
- Default Input Line Selections 73
- 7.6.2 Output Lines 74
- Basler racer GigE 65 75
- Using the Outputs with LVTTL 76
- 7.6.2.4 Output Line Inverters 77
- Sets user output 1 state 81
- Sets user output 2 state 81
- Not used 81
- 7.6.4 Checking the Line Logic 82
- 7.6.5 I/O Line Response Times 83
- 74 Basler racer GigE 84
- 8 Acquisition Control 85
- 76 Basler racer GigE 86
- Setting the Frame Parameters 87
- 8.2 Controlling Acquisition 88
- 80 Basler racer GigE 90
- Basler racer GigE 81 91
- Related Parameters 92
- 8.2.3 Frame Start Triggering 93
- 84 Basler racer GigE 94
- 8.2.3.4 Frame Timeout 96
- 8.2.4 Line Start Triggering 97
- 88 Basler racer GigE 98
- (duration determined by the 100
- 8.2.5 Exposure Time 102
- (Free Run), Single Frame Mode 105
- Basler racer GigE 97 107
- Frame Start Triggering On 109
- Line Start Triggering On 111
- Partial Closing Frame False 113
- Partial Closing Frame True 115
- Basler racer GigE 109 119
- Basler racer GigE 111 121
- 114 Basler racer GigE 124
- Line Acquisition N 125
- Line Acquisition N+1 125
- Basler racer GigE 117 127
- 5.4 µs 128
- Basler racer GigE 121 131
- 122 Basler racer GigE 132
- 8.3.1 Exposure Active Signal 133
- 8.3.3 Trigger Wait Signals 135
- 126 Basler racer GigE 136
- Basler racer GigE 127 137
- 128 Basler racer GigE 138
- Basler racer GigE 129 139
- 130 Basler racer GigE 140
- Basler racer GigE 131 141
- 132 Basler racer GigE 142
- Output Line 143
- 8.4 Frame Transmission Time 144
- 8.5 Maximum Allowed 145
- Line Acquisition Rate 145
- Basler racer GigE 137 147
- ExposureOverhead Parameter 148
- Removing the Parameter Limits 149
- 8.6 The Shaft Encoder Module 150
- Basler racer GigE 141 151
- 142 Basler racer GigE 152
- The Reverse Counter 153
- 144 Basler racer GigE 154
- 8.7 Frequency Converter 159
- 150 Basler racer GigE 160
- 9 Pixel Data Formats 161
- 9.2 Pixel Data Formats 162
- 9.2.2 Mono 12 Format 163
- 9.2.3 Mono 12 Packed Format 165
- 9.2.4 YUV 4:2:2 Packed Format 167
- 162 Basler racer GigE 172
- 10 Standard Features 173
- 10.1.1.1 Analog Gain 174
- 10.1.1.2 Digital Gain 174
- Setting the Digital Gain 175
- Gain Raw48.165–= 175
- 10.1.2 Black Level 176
- Basler racer GigE 167 177
- 10.2 Remove Parameter Limits 178
- 10.3 Image Area of Interest 179
- Setting Automatic X Centering 180
- 10.4 Event Reporting 181
- The Event Queue 182
- 10.5 Luminance Lookup Table 184
- 10.6 Binning 187
- 10.7 Gamma Correction 188
- 10.8 Shading Correction 189
- User Shading Set File 190
- Basler racer GigE 181 191
- 182 Basler racer GigE 192
- Basler racer GigE 183 193
- 10.9 Trigger Delay 194
- 10.10 Error Codes 195
- 186 Basler racer GigE 196
- 10.11Test Images 197
- 10.11.1Test Images in Detail 198
- Basler racer GigE 189 199
- 10.13 User Defined Values 202
- 10.14 Configuration Sets 203
- Default Startup Set 204
- Set into the Active Set 205
- 196 Basler racer GigE 206
- 11 Chunk Features 207
- Chunk Features AW00118302000 208
- 198 Basler racer GigE 208
- 11.3 Frame Counter 210
- Frame Counter Reset 211
- 202 Basler racer GigE 212
- 11.4 Time Stamp 213
- 204 Basler racer GigE 214
- Result.GetPayloadSize() ); 214
- 11.5 Trigger Counters 215
- Frame Trigger Counter = 0 216
- Frame Trigger Counter = 1 216
- Frame Trigger Counter = 2 216
- 11.6 Encoder Counter 218
- AW00118302000 Chunk Features 219
- Basler racer GigE 209 219
- 210 Basler racer GigE 220
- Basler racer GigE 211 221
- 11.8 CRC Checksum 222
- 214 Basler racer GigE 224
- 12.1 Camera Reset 225
- 12.2 Tech Support Resources 226
- 12.3 Obtaining an RMA Number 226
- Technical Support 226
- Revision History 229
- Basler racer GigE 221 231
- 222 Basler racer GigE 232
- AW00118302000 Index 233
- Basler racer GigE 223 233
- Index AW00118302000 234
- 224 Basler racer GigE 234
- Basler racer GigE 225 235
- 226 Basler racer GigE 236
- Basler racer GigE 227 237
- 228 Basler racer GigE 238
Related products and manuals for Bridge cameras Basler raL2048-48gm
Bridge cameras Basler SCOUT LIGHT User Manual
(166 pages)
(166 pages)
Bridge cameras Basler Camera User Manual
(11 pages)
(11 pages)
Bridge cameras Basler A101f User Manual
(46 pages)
(46 pages)
© 2020, manymanuals.com. All rights reserved. | 0.114 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals